search

Marathon Sprint Series Provozní pokyny Strana 10

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 35
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
    •
  • KNIHY
    • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 9
Installation sprint / marathon
9
For installation on the ceiling (D), drill holes at distances of
15 mm, if possible. Smaller angle of inclination of the fixing
brackets.
• The drive mechanism can be mounted on lintel (S) or ceiling (D).
• Measure front centre point (VM) of door and mark on door and on
lintel or ceiling.
• Make a mark 74 mm to right and left of centre of door (VM) at same
height on lintel or ceiling (see fig. 8).
• Drill two holes (Ø 10 x 65 mm).
Wear safety goggles when drilling!
Check thickness of ceiling, particularly with prefabricated
garages!
• Open door. Transfer door centre mark (HM) on to ceiling. Close door.
• Insert plug (1). Lift up drive mechanism (2) at front. Secure lintel
fitting (3) at front with two screws (4) and plain washers (5).
Protect control unit housing (6) from damage!
14
1
HM
3
2
5
4
B
600
0
1
13
12
12
2
6
4
5
3 1
11
10
`
0
1
5
`
½
15
`
0
1
5
`
½
½
`
0
1
5
`
½
½
`
0
1
5
`
½
½
`
0
1
5
`
½
½
`
0
1
5
`
½
½
`
0
1
5
`
½
½
`
0
1
4
5
6
7
H
M
P
T
V
`
m
°
HM
`
0
1
4
5
6
7
H
M
P
T
V
`
m
°
HM
`
0
1
4
5
6
7
H
M
P
T
V
`
m
°
HM
`
0
1
5
`
½
11
`
0
1
4
5
6
7
H
M
P
T
V
`
m
°
VM
74mm 74mm
10mm
`
0
1
4
5
6
7
H
M
P
T
V
`
m
°
65mm
10
THP
9
8
8
S
30
min.15
30
15
15
D
½
½
½
½
½
½
VM
VM
VM
9
Caution!
Mount the drive in parallel to the runner rails of the door.
• Lift up drive
• Align ceiling bracket (1). It should be located within a range of
B = 0 ... 600 mm.
• Align drive mechanism horizontally to rear centre of door (HM). Mark
position of holes. Drill two holes (Ø 10 x 65 mm deep).
Wear safety goggles when drilling!
Check thickness of ceiling, particularly with prefabricated
garages!
• Insert plug (1). Fit two screws (2) with plain washers (3). Tighten
screws (2) securely.
• Align C-rail (4) at correct height. If necessary, move screws (5).
Tighten screws (5).
• Mount drive shaft (1):
Insert the long bolt (2) and slide on the securing clip (3).
• Attach the door hinge (4) to the connecting rod (1) using the short
bolt (5) and slide on the securing clip (3).
• Pull once on emergency release wire (N), thus disengaging bogie
unit (1). Tighten screw (8) on lintel fitting.
• Use drive shaft (2) to push bogie unit (1) as far forward as possible
(3). If necessary, release cut-off buffer (4).
• Align angle of door fitting (5) with centre of door (VM) and mark
5 drill holes. Drill 5 holes (Ø 5 mm).
Use screws that are appropriate to the door material.
Wear safety goggles when drilling!
• Insert 5 hexagon-head screws (6) and tighten securely.
• Release cut-off buffer (4) and push right up to bogie unit (7).
• Tighten cut-off buffer screw (4) securely.
16
15
15
2
3
5
4
3
N
1
2
4 8
7
3
6
5
1
N
16
14
13
HM
Zobrazit stránku 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 34 35

Komentáře k této Příručce

Žádné komentáře
  • Vorzuge Casablanca Salamander-designs J. Mason Baker Road Furniture
  • Rollei Filmové kamery Pinnacle Design ne SYBA Přepínače KVM Regency ne Demco Příslušenství a součásti motorových vozidel
  • Blackstone 1575 Hampton Bay 14412 Samsung WW8TK5400UW AEG L6FBG49WC AEG A61900HLW0
  • Casio CTK-1300 Uživatelský manuál Sony VGN-S3HP Uživatelský manuál Jvc GY-HMZ1 Uživatelský manuál Sony PCK-LM11 Marketingové specifikace CE Labs HSW44C Uživatelský manuál